APC Power-Saving Back-UPS Pro 1500, 230V, Schuko

BR1500G-GR Features

APC Power-Saving Back-UPS Pro 1500, 230V, Schuko

• Adjustable voltage sensitivity
  Provides the ability to adapt the UPS for optimal performance in specific power environments or generator applications.
• Adjustable voltage-transfer points
  Maximizes useful battery life by widening the input voltage window or tightening the output voltage regulation.
• Audible alarms
  Provides notification of changing utility power and UPS power conditions
• Automatic self-test
  Periodic battery self-test ensures early detection of a battery that needs to be replaced.
• Automatic Voltage Regulation (AVR)
  Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment.
• Battery failure notification
  Provides early-warning fault analysis on batteries enabling timely preventive maintenance
• Battery replacement without tools
  Enables fast battery replacement, lowering Mean Time to Repair (MTTR).
• Battery-protected and surge-only outlets
  Reserves power capacity and run time for connected equipment that require UPS battery back-up while providing surge only protection for less critical equipment
• Boost and Trim Automatic Voltage Regulation (AVR)
  Eliminates voltage fluctuations as a source of AV signal degradation and component power-supply stress.
• Building Wiring Fault Indicator
  This LED informs users of potentially dangerous wiring problems in the wall circuit.
• Cold-start capable
  Provides temporary battery power when the utility power is out.
• Dataline surge protection
  Provides protection of connected equipment from power surges on the data lines.
• Disconnected battery notification
  Warns when a battery is not available to provide backup power.
• Extendable Run Time
  Additional batteries can be added to provide power to the load for an extended period of time in the event of utility supply failure.
• Green mode
  Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.
• Hot-swappable batteries
  Ensures clean, uninterrupted power to protected equipment while batteries are being replaced
• Intelligent battery management
  Maximizes battery performance, life, and reliability through intelligent, precision charging.
• LCD display
  Alpha-Numeric Display which displays system parameters and alarms.
• LCD graphics display
  Text and mimic diagrams that display modes of operation, system parameters and alarms.
• Power-saving outlets
  Automatically cuts power to idle equipment to conserve electricity.
• Resettable circuit breaker
  Easy recovery from overloads; no need to replace a fuse.
• Safety-agency approved
  Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.
• Serial connectivity
  Use any Home Automation network to monitor and control the S20 through its RS-232 serial port. For information on how to communicate with the S20, see APC’s Application Note #102. Crestron and AMX installers should visit their respective websites for information on how to integrate the S20 into those networks.
• Telephone dataline surge protection
  Provides protection of connected equipment from power surges traveling on telephone lines.
• Transformer-block spaced outlets
  Protect equipment with input transformer blocks without blocking access to other receptacles.
• USB connectivity
  Provides management of the UPS via a USB port (not available on all models).
• User-replaceable batteries
  Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)

Back-UPS Pro Features & Benefits

Manageability

• USB connection
  Use your PC to access additional power protection and management features for your UPS via a USB Port.
• LCD Status Display
  Provides key UPS status at a glance. Multiple status indicators with load and battery bar graphs.
• Audible alarms
  Provides notification of changing utility power and UPS power conditions
• Disconnected battery notification
  Warns when a battery is not available to provide backup power.

Marketing Features

• Battery-protected and surge-only outlets
  Reserves power capacity and run time for connected equipment that require UPS battery back-up while providing surge only protection for less critical equipment
• LCD Status Display
  Provides key UPS status at a glance. Multiple status indicators with load and battery bar graphs.
• Boost Automatic Voltage Regulation (AVR)
  Preserves battery life and maximizes runtime by correcting low voltages without discharging the battery.
• Energy Management Function
  Energy saving feature automatically power off peripherals when the a master device, usually a PC, hibernates or is shut down. Power to peripherals is immediately restored when the master device wakes up or is switched on.
• Green mode
  Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.

Serviceability

• Resettable circuit breaker
  Easy recovery from overloads; no need to replace a fuse.
• Simple battery replacement
  Increases UPS availability by allowing quick, easy battery replacement.

Availability

• Energy Management Function
  Energy saving feature automatically power off peripherals when the a master device, usually a PC, hibernates or is shut down. Power to peripherals is immediately restored when the master device wakes up or is switched on.
• Customizable voltage-transfer points
  Adjust the voltage points (widen or tighten the range) where your UPS transfers to battery to maximize useful battery life and protect sensitive electronics.
• Customizable voltage sensitivity
  Toggle between pre-determined voltage-transfer points depending on your power quality (high, medium or low sensitivity), maximizing useful battery life and protecting sensitive electronics.
• Boost and Trim Automatic Voltage Regulation (AVR)
  Gives higher application availability by correcting low and high voltage conditions without using the battery (not available on all models).
• Green mode
  Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.
• Automatic self-test
  Periodic battery self-test ensures early detection of a battery that needs to be replaced.
• Battery failure notification
  Provides early-warning fault analysis on batteries enabling timely preventive maintenance
• Cold-start capable
  Provides temporary battery power when the utility power is out.
• Intelligent battery management
  Maximizes battery performance, life, and reliability through intelligent, precision charging.
• Transformer-block spaced outlets
  Protect equipment with input transformer blocks without blocking access to other receptacles.

Protection

• Surge only outlets
  Protect secondary electronics from surges and spikes without reducing battery power used to run primary electronics during an outage.
• Battery and surge protected outlets
  Back up and protect your hardware and data during power outages, surges and spikes.
• Dataline surge protection
  Provides protection of connected equipment from power surges on the data lines.

Safety

• Safety-agency approved
  Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

Output

• Output power capacity

  865 Watts / 1.5 kVA

• Max Configurable Power (Watts)

  865 Watts / 1.5 kVA

• Nominal Output Voltage

  230V

• Output Frequency (sync to mains)

  50/60Hz +/- 3 Hz

• Output Frequency (not synced)

  60Hz +/- 0.1% for 60Hz nominal, 50Hz +/- 0.1% for 50Hz nominal

• Topology

  Line Interactive

• Waveform type

  Stepped approximation to a sinewave

• Output Connections
  (3) Schuko CEE 7 (selector_surgetitle)

  (3) Schuko CEE 7 (Battery Backup)
• Transfer Time

  10ms typical : 12ms maximum

Input

• Nominal Input Voltage

  230V

• Input frequency

  50/60 Hz +/- 3 Hz (auto sensing)

• Input Connections

  Schuko CEE 7/7P

• Cord Length

  1.83 meters

• Input voltage range for main operations

  176 – 294 V

• Input voltage adjustable range for mains operation

  156 – 300 V

Batteries & Runtime

• Typical recharge time

  8 hour(s)

• Replacement Battery

  APCRBC124

• RBC Quantity

  1

• Battery Volt-Amp-Hour Capacity

  187

• Runtime
  View Runtime Graph
  View Runtime Chart
• Efficiency
  View Efficiency Graph

Communications & Management

• Interface Port(s)

  Optional Simple Signalling RS232 cable , USB

• Control panel

  Multi-function LCD status and control console

Surge Protection and Filtering

• Surge energy rating

  441 Joules

• Data Line Protection

  RJ-11 Modem/Fax/DSL protection (two wire single line), RJ-45 Modem/Fax/DSL protection (four wire dual line)

Physical

• Maximum Height

  301 , 30.1 cm

• Maximum Width

  112 , 11.2 cm

• Maximum Depth

  382 , 38.2 cm

• Net Weight

  13.0 kg

• Shipping weight

  13.8 kg

• Shipping Height

  390 , 39.0 cm

• Shipping Width

  235 , 23.5 cm

• Shipping Depth

  490 , 49.0 cm

• Units per Pallet

  20.0

Environmental

• Operating Environment

  0 – 40 °C

• Operating Relative Humidity

  0 – 95 %

• Operating Elevation

  0-3000 meters

• Storage Temperature

  -15 – 45 °C

• Storage Relative Humidity

  0 – 95 %

• Storage Elevation

  0-15000 meters

• Audible noise at 1 meter from surface of unit

  45.0 dBA

Conformance

• Approvals

  BSI 1363, CE, ENERGY STAR (EU), NEMKO

• Equipment protection policy

  Lifetime : 200000 AUD, Lifetime : 150000 Euros, Lifetime : 75000 GBP

• Standard warranty

  2 years repair or replace, 3 years repair or replace for European Union countries

Sustainable Offer Status

• RoHS

  Compliant

• REACH

  REACH: Contains No SVHCs